Prepregs

prepreg carbon fiber, carbon prepreg, carbon fiber 1k t300, carbon fabric plain 90 g Carbon prepreg C90Ppp 1K, optimized for hot press TECHNICAL CHARACTERISTICS Fabric weight: 92 g / m2 Width: 1.00 meter Weaving style: Plain Warp: 1K T300 carbon fiber, 50%, 7 ends (threads) / cm Weft: 1K T300 carbon fiber, 50%, 7 ends / cm Prepreg weight: 167 g / m2 Epoxy content: 45% Volatile content: < 1%   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR RESPECTIVE CURING CYCLE 1 hour at 120 oC (248 oF): 110 - 120 oC (230 - 248 oF) 1 hour at 130 oC (266 oF): 130 - 140 oC (266 - 284 oF) 10 min at 150 oC (302 oF): 130 - 150 oC (266 - 302 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured at 130 oC for 60 minutes and 3 bar Flexural strength (Mpa): 850 Flexural modulus (Gpa): 54 Tensile strength (MPa): 550 Tensile modulus (GPa): 60 ILSS - Short Beam Shear (Mpa): 67 Tg (DSC) 20 oC / min: 128 oC   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fibre 3k tr30s, carbon fabric plain 160 g Carbon prepreg C160Ppp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 160 g / m2 Width: 1.00 meter Weaving style: Plain Warp: 3K TR30S carbon fiber, 50%, 4 ends (threads) / cm Weft: 3K TR30S carbon fiber, 50%, 4 ends (threads) / cm Prepreg weight: 291 g / m2 Epoxy content: 45% Gel time at 125 oC: 6-9 min Volatile content: < 1 %   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR SUGGESTED CURING CYCLE 1 hour at 125 oC (257 oF): 120 - 125 oC (248 - 257 oF) 2 hours at 110 oC (230 oF): 120 - 125 oC (248 - 257 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured by hot press technology at 125 °C curing cycle Flexural strength (Mpa): 800 Flexural modulus (GPa): 54 ILSS - Short Beam Shear (Mpa): 64   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fibre 3k tr30s, carbon fabric twill 160 g Carbon prepreg C160T2pp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 160 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 3K TR30S carbon fiber, 50%, 5.25 ends (threads) / cm Weft: 3K TR30S carbon fiber, 50%, 5.25 ends / cm Prepreg weight: 394 g / m2 Epoxy content: 42 % Gel time at 125 oC: 11 min Volatile content: < 1 % Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR RESPECTIVE CURING CYCLE 1 hour at 120 oC (248 oF): 110 - 120 oC (230 - 248 oF) 1 hour at 130 oC (266 oF): 130 - 140 oC (266 - 284 oF) 10 min at 150 oC (302 oF): 130 - 150 oC (266 - 302 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured at 130 oC for 60 minutes and 3 bar Flexural strength (Mpa): 850 Flexural modulus (Gpa): 54 Tensile strength (MPa): 550 Tensile modulus (GPa): 60 ILSS - Short Beam Shear (Mpa): 67 Tg (DSC) 20 oC / min: 128 oC   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fibre 3k tr30s, carbon fabric twill 200 g Carbon prepreg C210T2pp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 206 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 3K TR30S carbon fiber, 49.5%, 5.10 ends (threads) / cm Weft: 3K TR30S carbon fiber, 50.5%, 5.20 ends / cm Prepreg weight: 381 g / m2 Epoxy content: 46% Gel time at 125 oC: 6-9 min Volatile content: < 1%   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR SUGGESTED CURING CYCLE 1 hour at 125 oC (257 oF): 120 - 125 oC (248 - 257 oF) 2 hours at 110 oC (230 oF): 120 - 125 oC (248 - 257 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured by hot press technology at 125 °C curing cycle Flexural strength (Mpa): 800 Flexural modulus (GPa): 54 ILSS - Short Beam Shear (Mpa): 64   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fiber 3k tr30s, carbon fabric plain 200 g, carbon prepreg for hot press Carbon prepreg C211T2pp, optimized for hot press   TECHNICAL CHARACTERISTICS Fabric weight: 206 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 3K TR30S carbon fiber, 49.5%, 5.10 ends (threads) / cm Weft: 3K TR30S carbon fiber, 50.5%, 5.20 ends / cm Prepreg weight: 381 g / m2 Epoxy content: 46% Volatile content: < 1%   RECOMMENDED CURING CYCLES 8 min at 150 oC (302 oF) 10 min at 145 oC (293 oF) 15 min at 140 oC (284 oF)   STORAGE LIFE 12 months at - 18 oC 3 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibermax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fiber 3k tr30s, carbon fabric twill 200 g, carbon prepreg out of autoclave Carbon prepreg C212T2pp, suitable for out of autoclave.   TECHNICAL CHARACTERISTICS Fabric weight: 206 g / m2 Width: 1.27 meters Weaving style: Twill 2X2 Warp: 3K TR30S carbon fiber, 49.5%, 5.10 ends (threads) / cm Weft: 3K TR30S carbon fiber, 50.5%, 5.20 ends / cm Prepreg weight: 322 g / m2 Epoxy content: 36%   For recommended curing cycles and process descriptions, please refer to the Technical Data Sheet.   STORAGE LIFE 12 months at - 18 oC 5 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fibre 3k tr30s, carbon fabric twill 240 g, carbon prepreg out of autoclave Carbon prepreg C242T2pp, suitable for out of autoclave (vacuum bagging) as well as press or autoclave processes. Both sides of the fabric are impregnated with a resin film.   TECHNICAL CHARACTERISTICS Fabric weight: 240 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 3K TR30S carbon fiber, 50%, 6 ends (threads) / cm Weft: 3K TR30S carbon fiber, 50%, 6 ends / cm Prepreg weight: 400 g / m2 Epoxy content: 40%   RECOMMENDED OUT OF AUTOCLAVE CURING CYCLES 2 h at 100 oC (Tg 120 oC) 3 h at 90 oC (Tg 115 oC) 12 h at 80 oC (Tg 110 oC) 5 h at 80 oC (Tg 105 oC) 18 h at 70 oC (Tg 100 oC)   RECOMMENDED OUT OF AUTOCLAVE PROCEDURE Apply maximum vacuum pressure from the start of the curing cycle, using one vacuum valve per sqm of surface area. Maintain a high vacuum level, typically around 980 mbar. Place monitoring thermocouples on the surface to control curing cycle,  in areas with the highest thermal mass or slowest heating rate.  Increase the temperature at a controlled rate of 1 °C/min from room temperature to 80 °C. Maintain the cure temperature at 80 °C. Start the curing cycle dwell once the slowest monitoring thermocouple reaches 80 °C. Hold the dwell for 300 minutes. After curing, cool at a controlled rate of 1–2 °C/min to either room temperature or 30 °C, whichever is higher.   For recommended curing cycles and process descriptions of other methods, please refer to the Technical Data Sheet.   STORAGE LIFE 12 months at - 18 oC 5 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fibre 3k t300, carbon fabric twill 285 g Carbon prepreg C285T2pp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 285 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 3K T300 carbon fiber, 50%, 7 ends (threads) / cm Weft: 3K T300 carbon fiber, 50%, 7 ends / cm Prepreg weight: 500 g / m2 Epoxy content: 42% Gel time at 125 oC: 11 min Volatile content: < 1%   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR RESPECTIVE CURING CYCLE 1 hour at 120 oC (248 oF): 110 - 120 oC (230 - 248 oF) 1 hour at 130 oC (266 oF): 130 - 140 oC (266 - 284 oF) 10 min at 150 oC (302 oF): 130 - 150 oC (266 - 302 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured at 130 oC for 60 minutes and 3 bar Flexural strength (Mpa): 850 Flexural modulus (Gpa): 54 Tensile strength (MPa): 550 Tensile modulus (GPa): 60 ILSS - Short Beam Shear (Mpa): 67 Tg (DSC) 20 oC / min: 128 oC   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fiber 3k t300, carbon fabric twill 285 g Carbon prepreg C285T4pp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 285 g / m2 Width: 1.00 meter Weaving style: Twill 4X4 Warp: 3K T300 carbon fiber, 50%, 7 ends (threads) / cm Weft: 3K T300 carbon fiber, 50%, 7 ends / cm Prepreg weight: 510 g / m2 Epoxy content: 44% Gel time at 125 oC: 6-9 min Volatile content: < 1 %   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 5 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR SUGGESTED CURING CYCLE 1 hour at 125 oC (257 oF): 120 - 125 oC (248 - 257 oF) 2 hours at 110 oC (230 oF): 120 - 125 oC (248 - 257 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured by hot press technology at 125 oC curing cycle Flexural strength (Mpa): 805 Flexural modulus (Gpa): 51 ILSS - Short Beam Shear (Mpa): 61   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fiber 12k tr50s, carbon fabric unidirectional 420 g Carbon prepreg C420Upp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 420 g / m2 Width: 1.00 meter Weaving style: Unidirectional, woven Warp: 12K TR50S carbon fiber, 92%, 5.00 ends (threads) / cm Weft: Glass thermoplastic 8%, 1.60 ends (threads) / cm Prepreg weight: 680 g / m2 Epoxy content: 38% Gel time at 125 oC: 11 min Volatile content: < 1%   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR RESPECTIVE CURING CYCLE 1 hour at 120 oC (248 oF): 110 - 120 oC (230 - 248 oF) 1 hour at 130 oC (266 oF): 130 - 140 oC (266 - 284 oF) 10 min at 150 oC (302 oF): 130 - 150 oC (266 - 302 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured at 130 oC for 60 minutes and 3 bar Flexural strength (Mpa): 850 Flexural modulus (Gpa): 59 Tensile strength (MPa): 650 Tensile modulus (GPa): 59 ILSS - Short Beam Shear (Mpa): 65 Tg (DSC) 20 oC / min: 140 oC   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fiber 12k t700, carbon fabric twill 428 g Carbon prepreg C428T2pp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 428 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 12K T700 carbon fiber, 50%, 2.7 ends (threads) / cm Weft: 12K T700 carbon fiber, 50%, 2.7 ends / cm Prepreg weight: 740 g / m2 Epoxy content: 42% Gel time at 125 oC: 6-9 min Volatile content: < 1%   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 5 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR SUGGESTED CURING CYCLE 1 hour at 125 oC (257 oF): 120 - 125 oC (248 - 257 oF) 2 hours at 110 oC (230 oF): 120 - 125 oC (248 - 257 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured by hot press technology at 125 oC curing cycle Flexural strength (Mpa): 800 Flexural modulus (Gpa): 52 ILSS - Short Beam Shear (Mpa): 64   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..

prepreg carbon fiber, carbon prepreg, carbon fibre 3k tr30s, carbon fabric twill 200 g Carbon prepreg C630T2pp, general purpose   TECHNICAL CHARACTERISTICS Fabric weight: 616 g / m2 Width: 1.00 meter Weaving style: Twill 2X2 Warp: 12K HS carbon fiber, 49.4%, 3.8 ends (threads) / cm Weft: 12K HS carbon fiber, 50.6%, 3.9 ends / cm Prepreg weight: 978 g / m2 Epoxy content: 37% Gel time at 125 oC: 6-9 min Volatile content: < 1%   Fibermax general purpose prepregs are based on a 80 to 150 oC (176 - 302 oF) curing toughened epoxy matrix, suited for both autoclave and press molding applications. A standard autoclave curing cycle is: Draw vacuum (0.6 - 0.7 bar) and apply positive pressure. Then start heating - typically 2-5 oC / min (3.5 - 9 oF) - till 120 oC (248 oF) and then hold this temperature for 1 hour. Turn off the temperature and cool under pressure to 60 oC (140 oF). When fully cooled open the bag and extract the piece.   STORAGE LIFE 12 months at - 18 oC 4 - 6 weeks at room temperature Allow prepreg roll to reach room temperature before opening plastic bag to prevent condensation.   EVALUATED Tg FOR SUGGESTED CURING CYCLE 1 hour at 125 oC (257 oF): 120 - 125 oC (248 - 257 oF) 2 hours at 110 oC (230 oF): 120 - 125 oC (248 - 257 oF)   TYPICAL MECHANICAL PROPERTIES OF LAMINATE Cured by hot press technology at 125 °C curing cycle Flexural strength (Mpa): 800 Flexural modulus (GPa): 54 ILSS - Short Beam Shear (Mpa): 64   Please click on picture, for a closer view to the fabric's real size. To realize actual size with precision please observe the threads / cm feature mentioned above.   DISCLAIMER All information herein is given for guidance and general information purposes only, represents typical properties, and should not be used for specification limits purposes or basis for design. Fibremax Ltd reserves the right to make modifications on fabrics, change yarns, specifications, and all information given herein, without notice. It is only on written certificates and agreements that we provide our customers with warrants for the quality and/or advise for the suitability of products for particular uses. Data sheets and certificates of conformity are promptly provided upon request with roll serial number.   Intrastat Number for this product: 59039010..