Epoxy systems

  High performance epoxy laminating system SR1700/SD2806 with fast hardener   Each kilo includes 0.72 kg resin + 0.28 kg hardener   High modulus, very stiff system, with low water absorption when cured and excellent adhesion to all types of reinforcements (carbon, aramid, glass etc). This system was developed for automotive, naval, and aerospace applications.   The 2806 and 2803 hardeners can be mixed in any proportion to achieve the required reactivity. The fast hardener 2806 offers fast laminate hardening at ambient temperature from 10 to 40 oC / 50 to 104 oF and can be slowed down by 2803. Good mechanical properties are achieved after room temperature curing, awesome after post curing.   Fast hardener SD2806 Fast reactivity, short working time, for laminating thin composites. Awesome mechanical properties, parts can be released after 24 hours at 18 oC / 64.4 oF. Mechanical properties are optimized by post-curing at 50-55 oC / 122-131 oF. Designed for the manufacturing of high performance composites, with a service temperature up to 70-80 oC / 158-176 oF.   PROPERTIES Physical properties of SR1700 epoxy resin Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC / 68 oF: 1950 Density at 20 oC / 68 oF: 1.16   Physical properties of SD2806 hardener Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC / 68 oF: 300 ± 60 Density (g/cm3) at 20 oC / 68 oF: 1.07 ± 0.01   Mix properties of SR1700 / SD2806 system Weight ratio: 100 / 39 g Volume ratio: 100 / 43 ml Mix viscosity at 20 oC / 68 oF: 940   Reactivity of SR1700 / SD2806 system Pot life on 500 g mix at 20 oC: 27' Exothermic peak on 500 g mix at 20 oC: > 210 oC / 410 oF Time to reach exothermic peak at 20 oC / 68 oF: 23'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  High performance epoxy laminating system SR1700 / SD2803 with medium hardener   Each kilo includes 0.72 kg resin + 0.28 kg hardener   High modulus, very stiff system, with low water absorption when cured and excellent adhesion to all types of reinforcements (carbon, aramid, glass etc). This system was developed for automotive, naval, and aerospace applications.   The 2803 and 2806 hardeners can be mixed in any proportion to achieve the required reactivity. The fast hardener 2806 offers fast laminate hardening at ambient temperature from 10 to 40 oC and can be slowed down by 2803. Good mechanical properties are achieved after room temperature curing, awesome after post curing.   Medium hardener SD2803: Slow reactivity, long working time, for laminating medium thickness composites. Good mechanical properties, parts can be released after 24 hours at 18 oC. Mechanical properties are optimized by post-curing at 50-55 oC. Designed for the manufacturing of high performance composites, with a service temperature up to 60-70 oC. PROPERTIES Physical properties of SR1700 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 1950 (+- 200) Density at 20 oC: 1.16 (+-0.01) Physical properties of SD2803 hardener: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 140 (+-30) Density (g/cm3) at 20 oC: 1.00 (+-0.01) Mix properties of SR1700 / SD2803 system: Weight ratio: 100 / 39 g Volume ratio: 100 / 45 ml Mix viscosity at 20 oC: 700 (+-100) Reactivity of SR1700 / SD2803 system: Pot life on 500 g mix at 20 oC: 2 h 10' Exothermic peak on 500 g mix (oC) at 20 oC: 200 oC Time to reach exothermic peak at 20 oC: 1 h 58'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  High performance epoxy laminating system SR1700 / SD7820 with slow hardener   Each kilo includes 0.74 kg resin + 0.26 kg hardener   High modulus, very stiff system, with low water absorption when cured and excellent adhesion to all types of reinforcements (carbon, aramid, glass etc). This system was developed for automotive, naval, and aerospace applications.   Slow hardener SD7820: Slow hardener, very low viscosity allowing fast reinforcements to wet out. Laminates require 6 to 8 hours of working time. It is adapted to the production of parts with a service temperature up to 120°C. Items can be handled and extracted from moulds after 12 hours at 40°C or 8 h at 60°C. PROPERTIES Physical properties of SR1700 epoxy resin: Aspect / colour: Yellow liquid Viscosity (mPa.s) at 20 oC: 1950 (+- 200) Density at 20 oC: 1.16 (+-0.01) Physical properties of SD7820 hardener: Aspect / colour: Clear liquid Viscosity (mPa.s) at 20 oC: 80 ± 15 Density (g/cm3) at 20 oC: 0.96 ± 0.01 Mix properties of SR1700 / SD7820 system: Weight ratio: 100 / 36 g Volume ratio: 100 / 43 ml Mix viscosity at 20 oC: 750 ± 150 Reactivity of SR1700 / SD7820 system: Exothermic peak on 500 g mix (oC) at 20 oC: 140 oC Time to reach exothermic peak at 20 oC: 9 h 30' Pot life on 500 g mix at 20 oC: 8 h 45'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Laminating epoxy system SR8200 / SD7203 with medium hardener Each kilo includes 0.73 kg resin + 0.27 kg hardener The SR8200 / SD7203 system exhibits very good mechanical properties, high elongation, fatigue resistance, low odor during application and relatively low cost. The maximum temperature resistance is at least 90 oC; however, some post curing is required in order to have service temperature of 60 - 70 oC. Typical applications include bows, masts and long service bending products. Medium hardener SD7203: Offers fast hardening of laminates at ambient temperature for hand laminating, press or vacuum. Good mechanical properties at ambient temperature, excellent after post cure. PROPERTIES Physical properties of SR8200 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 2900 ± 600 Density at 20 oC: 1.175 ± 0.01 Physical properties of SD7203 hardener: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 120 ± 25 Density at 20 oC: 1.01 ± 0.01 Mix properties of SR8200 / SD7203 system: Weight ratio: 100 / 37 g Volume ratio: 100 / 43 ml Mix viscosity at 20 oC: 1050 ± 200 Reactivity of SR8200 / SD7203 system: Pot life for 100 g mix at 25 oC: 2 h 33' Exothermic temperature for 100 g mix at 20 oC: 40 oC Time to reach exothermic peak for 100 g mix at 20 oC: 4 h 26'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Laminating epoxy system SR8200 / SD7201 with slow hardener Each kilo includes 0.73 kg resin + 0.27 kg hardener The SR8200 / SD7201 system exhibits very good mechanical properties, high elongation, fatigue resistance, low odor during application and relatively low cost. The maximum temperature resistance is at least 90 oC; however, some post curing is required in order to have service temperature of 60 - 70 oC. Typical applications include bows, masts and long service bending products. Slow hardener SD7201: Reactivity formulated for hand laminating, under press or medium to large parts under vacuum. Requires a post-cure at 55°C to 60°C. Designed for manufacturing of high performance composites and tooling with service temperature of 60°C to 70°C. PROPERTIES Physical properties of SR8200 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 2900 ± 600 Density at 20 oC: 1.175 ± 0.01 Physical properties of SD7201 hardener: Aspect / colour: Clear to yellow liquid Viscosity (mPa.s) at 20 oC: 60 ± 15 Density at 20 oC: 0.95 ± 0.01 Mix properties of SR8200 / SD7201 system: Weight ratio: 100 / 37 g Volume ratio: 100 / 46 ml Mix viscosity at 20 oC: 790 ±150 Reactivity of SR8200 / SD7201 system: Pot life for 100 g mix at 30 oC: 2 h 56' Exothermic temperature for 100 g mix at 20 oC: 25 oC Time to reach exothermic peak for 100 g mix at 20 oC: 8 h    Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Versatile epoxy system SR8200 / SD4775 with medium hardener Each kilo includes 0.78 kg resin + 0.22 kg hardener Applications: - Hand laminating - Infusion - Adhesive - Tooling - Casting - Laminate PROPERTIES Physical properties of SR8200 epoxy resin: Aspect / colour: Viscous liquid Viscosity (mPa.s) at 20 oC: 2900 ± 600 Density at 20 oC: 1.175 ± 0.005 Physical properties of SD4775 hardener: Aspect / colour: Clear liquid Viscosity (mPa.s) at 20 oC: 190 ± 40 Density at 20 oC: 1.010 ± 0.005 Mix properties of SR8200 / SD4775 system: Weight ratio: 100 / 28 g Volume ratio: 100 / 33 ml Mix viscosity at 20 oC: 1000 ± 200 Reactivity of SR8200 / SD4775 system: Exothermic temperature for 500 g mix at 20 oC: 262 oC Time to reach exothermic peak for 500 g mix at 20 oC: 55' Pot life of 500 g mix at 20 oC: 39'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Versatile epoxy system SR8500 / SD8605 for composite applications with fast hardener Each kilo includes 0.74 kg resin + 0.26 kg hardener The SR8500 / SD8605 system allows manufacturing of multiple kinds of composite parts that can work up to 70 oC continuously. Solvent and reactive diluent free, without any aromatic or CMR amines and very simple handling: One resin and two hardeners mixable in any proportions to achieve the desired reactivity. Curing at ambient temperature and post curing at 40 to 60 oC.       Germanischer Llyod's certified Fast hardener SD8605: Can be used as an accelerator for hardener SD8601. Reactivity adapted for the manufacturing of small parts. Good mechanical properties after ambient curing. Applications: Hand laminating Injection Filament winding Cold or Hot press moulding Casting Adhesive PROPERTIES Physical properties of SR8500 epoxy resin: Aspect / colour: Clear liquid Viscosity (mPa.s) at 20 oC: 9 800 ± 1 000 Density at 20 oC: 1.176 ± 0.05 Physical properties of SD8605 hardener: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 400 ± 80 Density at 20 oC: 1.02 ± 0.01 Mix properties of SR8500 / SD8605 system: Weight ratio: 100 / 35 Volume ratio: 100 / 40 Mix viscosity at 20 oC: 2800 (+-450) Reactivity of SR8500 / SD8605 system: Pot life on 500 g mix at 20 oC: 31' Exothermic peak (oC) on 500 g mix at 20 oC: 237 Time to reach exothermic peak on 500 g mix at 20 oC: 39'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Versatile epoxy system SR8500 / SD8601 for composite applications with slow hardener Each kilo includes 0.74 kg resin + 0.26 kg hardener The SR8500 / SD8601 system allows manufacturing of multiple kinds of composite parts that can work up to 70 oC continuously. Solvent and reactive diluent free, without any aromatic or CMR amines and very simple handling: One resin and two hardeners mixable in any proportions to achieve the desired reactivity. Curing at ambient temperature and post curing at 40 to 60 oC.       Germanischer Llyod's certified Slow hardener SD8601: Reactivity adapted for manufacturing of large parts. Should be post cured at 40 oC before demoulding. Applications: Hand laminating Injection Filament winding Cold or Hot press moulding Casting Adhesive PROPERTIES Physical properties of SR8500 epoxy resin: Aspect / colour: Clear liquid Viscosity (mPa.s) at 20 oC: 9800 (+-1000) Density at 20 oC: 1.176 (+-0.05) Physical properties of SD8601 hardener: Aspect / colour: Clear liquid Viscosity (mPa.s) at 20 oC: 15 (+-3) Density at 20 oC: 0.950 (+-0.01) Mix properties of SR8500 / SD8601 system: Weight ratio: 100 / 35 Volume ratio: 100 / 43 Mix viscosity at 20 oC: 750 (+-150) Reactivity of SR8500 / SD8601 system: Pot life on 500 g mix at 25 oC: 7 h 25' Exothermic peak (oC) on 500 g mix 20 oC: 33 Time to reach exothermic peak on 500 g mix at 20 oC: 15 h 10'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Structural epoxy system SR1710 / SD8824 for vacuum infusion and RTM with fast hardener Each kilo includes 0.81 kg resin + 0.19 kg hardener Two component epoxy system, specially designed for Resin Transfer Molding process, vacuum infusion, injection, etc. It may also be used in hand layup (for flat surface molds or molds with no vertical surfaces). It exhibits very high mechanical properties, especially interlaminar shear strength. This system has a very low viscosity, and low reactivity for manufacturing of large parts. It also exhibits excellent retention of the mechanical characteristics in a wet environment. Temperature resistance: Tg1 max = 100 oC       Germanischer Llyod's certified PROPERTIES Physical properties of SR1710 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 1550 ± 350 Density (g/cm3) at 20 oC: 1.1500 Physical properties of SD8824 hardener: Aspect / colour: Light yellowish liquid Viscosity (mPa.s) at 20 oC: 6 (+- 2) Density (g/cm3) at 20 oC: 0.944 Mix properties of SR1710 / SD8824 system: Mix viscosity (mPa.s) at 20 oC: 290 (+-30) Mixing ratio by weight: 100 g / 23 g Mixing ratio by volume: 100 ml / 28 ml Reactivity of SR1710 / SD8824 system: Pot life on 500 g mix at 20 oC: 2 h 30' Exothermic temperature (oC) on 500 g mix at 20 oC: 215 Time to reach the exothermic peak on 500 g mix at 20 oC: 2 h 40' Polymerisation of SD8824 hardener: Time to wait at 20 oC before post-curing*: 6 hours Minimum post-cure cycle: 24 hours at 40 oC Advised post-cure cycle: 8 hours at 60 oC *has to be respected in case of thick laminate (> 3 mm,) so to limit the risk of exothermic reaction.   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Epoxy system SR8100 / SD8824 for injection and infusion with fast hardener Each kilo includes 0.82 kg resin + 0.18 kg hardener The SR8100 is a 2 component epoxy system specially formulated for resin transfer processes, such as injection and infusion. This system has a very low viscosity at ambient temperature. The two different hardeners (SD8822 and SD8824) allow moulding of small to large parts, with fast demoulding times, high mechanical properties and good price. The cured system gives a temperature resistance up to 80 oC (Tg 1).       Germanischer Llyod's certified            Lloyd's Register certified PROPERTIES Physical properties of SR8100 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 1250 ± 250 Density (g/cm3) at 20 oC: 1.158 Physical properties of SD8824 hardener: Aspect / colour: Light yellowish liquid Viscosity (mPa.s) at 20 oC: 6 (+-2) Density (g/cm3) at 20 oC: 0.944 Physical properties of SD8822 - SD8824 hardeners mix (50/50 by weight): Aspect / colour: Light yellowish liquid Viscosity (mPa.s) at 20 oC: 9 (+-3) Density (g/cm3) at 20 oC: 0.942 (+-0.01) Mix properties of SR8100 / SD8824 system: Mix viscosity (mPa.s) at 20 oC: 300 Mixing ratio by weight: 100 g / 22 g Mixing ratio by volume: 100 ml / 27 ml Mix properties of SR8100 / SD8822-SD8824 (50/50 by weight) system: Mix viscosity (mPa.s) at 20 oC: 340 (+-100) Mixing ratio by weight: 100 g / 26 g Mixing ratio by volume: 100 ml / 32 ml Reactivity of SR8100 / SD8824 system: Pot life on 500 g mix at 20 oC: 1 h 21' Exothermic temperature on 500 g mix (oC) at 20 oC: 210 Time to reach the exothermic peak on 500 g mix at 20 oC: 1 h 27' Reactivity of SR8100 / SD8822-SD8824 (50/50 by weight) system: Pot life on 500 g mix at 20 oC: 1 h 55' Exothermic temperature on 500 g mix (oC) at 20 oC: >210 Time to reach the exothermic peak on 500 g mix at 20 oC: 2 h 05' Polymerisation of SD8824 hardener under temperature: Gel time on resin film at 40 oC: 1 h 07' Gel time on resin film at 60 oC: 26' Gel time on resin film at 80 oC: 10'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Epoxy system SR8100 / SD8822 for injection and infusion with slow hardener Each kilo includes 0.76 kg resin + 0.24 kg hardener The SR8100 is a 2 component epoxy system specially formulated for resin transfer processes, such as injection and infusion. This system has a very low viscosity at ambient temperature. The two different hardeners (SD8822 and SD8824) allow moulding of small to large parts, with fast demoulding times, high mechanical properties and good price. The cured system gives a temperature resistance up to 80 oC (Tg 1).       Germanischer Llyod's certified            Lloyd's Register certified PROPERTIES Physical properties of SR8100 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (mPa.s) at 20 oC: 1320 (+-100) Density (g/cm3) at 20 oC: 1.158 Physical properties of SD8822 hardener: Aspect / colour: Light yellowish liquid Viscosity (mPa.s) at 20 oC: 20 (+-4) Density (g/cm3) at 20 oC: 0.937 Physical properties of SD8822-SD8824 hardeners mix (50/50 by weight): Aspect / colour: Light yellowish liquid Viscosity (mPa.s) at 20 oC: 9 (+-3) Density (g/cm3) at 20 oC: 0.942 (+-0.01) Mix properties of SR8100 / SD8822 system: Mix viscosity (mPa.s) at 20 oC: 390 (+-100) Mixing ratio by weight: 100 g / 31 g Mixing ratio by volume: 100 ml / 39 ml Mix properties of SR8100 / SD8822-SD8824 (50/50 by weight) system: Mix viscosity (mPa.s) at 20 oC: 340 (+-100) Mixing ratio by weight: 100 g / 26 g Mixing ratio by volume: 100 ml / 32 ml Reactivity of SR8100 / SD8822 system: Pot life on 500 g mix at 20 oC: 3 h 08' Exothermic temperature on 500 g mix (oC) at 20 oC: 205 Time to reach the exothermic peak on 500 g mix at 20 oC: 3 h 30' Reactivity of SR8100 / SD8822-SD8824 (50/50 by weight) system: Pot life on 500 g mix at 20 oC: 1 h 55' Exothermic temperature on 500 g mix (oC) at 20 oC: >210 Time to reach the exothermic peak on 500 g mix at 20 oC: 2 h 05' Polymerisation of SD8822 hardener under temperature: Gel time on resin film at 40 oC: 2 h 33' Gel time on resin film at 60 oC: 56' Gel time on resin film at 80 oC: 23'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Epoxy system SR8100 / SD4771 for injection and infusion with ultra slow hardener Each kilo includes 0.78 kg resin + 0.22 kg hardener The SR8100 is a 2 component epoxy system specially formulated for resin transfer processes, such as injection and infusion. This system has a very low viscosity at ambient temperature. The different hardeners allow moulding of small to large parts, with fast demoulding times, high mechanical properties and good price. The cured system gives a temperature resistance up to 80 oC (Tg 1). The hardener SD4771 is designed for very thick fibers laminates. PROPERTIES Physical properties of SR8100 epoxy resin: Aspect / colour: Yellow liquid Viscosity (mPa.s) at 20 oC: 1320 (+-260) Density (g/cm3) at 20 oC: 1.158 Physical properties of SD4771 hardener: Aspect / colour: Light yellow liquid Viscosity (mPa.s) at 20 oC: 11 (+-2) Density (g/cm3) at 20 oC: 0.944 Mix properties of SR8100 / SD4771 system: Mix viscosity (mPa.s) at 20 oC: 400 Mixing ratio by weight: 100 g / 29 g Mixing ratio by volume: 100 ml / 36 ml Reactivity of SR8100 / SD4771 system: Exothermic temperature on 500 g mix (oC) at 20 oC: 200 Time to reach the exothermic peak on 500 g mix at 20 oC: 5 h 15' Time to reach 50 oC on 500 g mix at 20 oC: 4 h 40'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Bio based versatile epoxy system SR GreenPoxy 56 / SD7561 with slow hardener Each kilo includes 0.74 kg resin + 0.26 kg hardener SR GreenPoxy 56 resin is based on the latest innovations in green chemistry and represents a significant technological breakthrough on the following points: purity, color, performance and guarantees on the availability of industrial tonnages. SR GreenPoxy 56 molecular structure is bio-based at almost 51% and is produced with a high carbon content of plant origin.   Applications: - Contact laminating (mold or industrial part) - Injection - Filament winding - Hot or cold press - Little casting PROPERTIES Physical properties of SR GreenPoxy 56 epoxy resin: Aspect / colour: Liquid colourless Viscosity (mPa.s) at 20 oC: 1600 ± 300 Density (g/cm3) at 20 oC: 1,1980 Physical properties of SD7561 hardener: Aspect / colour: Liquid colourless Viscosity (mPa.s) at 20 oC: 60 ± 15 Density (g/cm3) at 20 oC: 0,9710 Mix properties of SR GreenPoxy 56 / SD7561 system: Mix viscosity (mPa.s) at 20 oC: 700 Mixing ratio by weight: 100 g / 36 g Mixing ratio by volume: 100 ml / 45 ml   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Clear bio based epoxy system SR GreenPoxy 56 / SZ8525 for hot process Each kilo includes 0.80 kg resin + 0.20 kg hardener SR GreenPoxy 56 resin is based on the latest innovations in green chemistry and represents a significant technological breakthrough on the following points: purity, color, performance and guarantees on the availability of industrial tonnages. SR GreenPoxy 56 molecular structure is bio-based at almost 51% and is produced with a high carbon content of plant origin.   The SR GreenPoxy 56 / SZ8525 epoxy system exhibits high mechanical and good wetting out properties resulting in a low resin consumption and a clear laminate and final aspect. The recommended cycle of 10 min is at 100°C and the mix bio-based carbon content of about 45%. PROPERTIES Physical properties of SR GreenPoxy 56 epoxy resin: Aspect / colour: Liquid colourless Viscosity (mPa.s) at 20 oC: 1400 Density (g/cm3) at 20 oC: 1,1980 Physical properties of SZ8525 hardener: Aspect / colour: Light yellow liquid Viscosity (mPa.s) at 20 oC: 33 Density (g/cm3) at 20 oC: 0.94 ± 0.01 Mix properties of SR GreenPoxy 56 / SZ8525 system: Mix viscosity (mPa.s) at 20 oC: 1160 Mixing ratio by weight: 100 g / 25 g Mixing ratio by volume: 100 ml / 32 ml   Reactivity of SR GreenPoxy 56 / SZ8525 system: Exothermic peak on 500 g mix at 20 oC: 280 Time to reach exothermic peak on 500 g mix at 20 oC: 27' Time to reach 50 °C on 500 g mix at 20 oC: 19'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Marine epoxy system SR5550 / SD5506 with very fast hardener Each kilo includes 0.78 kg resin + 0.22 kg hardener The SR5550 is specially formulated for ambient temperature curing of marine and wood composites (laminating, bonding and protection of wood.) It has an excellent adhesion to all types of wood. It is handy, with adjustable working time, has low viscosity, and is crystallization free. Suitable for room temperature applications, it gives a high gloss finish, with low surface pollution, and UV stability. This marine epoxy system has a low toxicity and should be preferred for laminating composite applications where post curing is not possible. Curing: SR5550 epoxy system cures at ambient temperature. Full cure after: 7 days at 25 oC or 48 hrs at 30 oC or 12 hrs at 40 oC or 6 hrs at 60 oC. PROPERTIES Physical properties of SR5550 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (m.Pas +-20%) at 20 oC: 1300 Density (g/cm3) at 20 oC: 1.145 Physical properties of SD5506 hardener: Aspect / colour: Yellow liquid Viscosity (m.Pas +-20%) at 20 oC: 1100 Density (g/cm3) at 20 oC: 1.07 Mix properties of SR5550 / SD5506 system: Viscosity of the mix (m.Pas +-20%) at 20 oC: 1800 Weight ratio: 100 / 29 g Volume ratio: 100 / 33 ml or 3 / 1 Reactivity of SR5550 / SD5506 system: Pot life for 100 g mix at 20 oC: 15' Exothermic temperature (oC) for 100 g mix at 20 oC: 200 Time to reach the exothermic temperature for 100 g mix at 20 oC: 20' Drying time, set to touch on 1 mm wet film at 20 oC: 1 h 35' Time before sanding at 25 oC: 2 h 30'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Marine epoxy system SR5550 / SD5503 with slow hardener Each kilo includes 0.78 kg resin + 0.22 kg hardener The SR5550 is specially formulated for ambient temperature curing of marine and wood composites (laminating, bonding and protection of wood.) It has an excellent adhesion to all types of wood. It is handy, with adjustable working time, as it comes with 2 hardeners (fast and slow,) has low viscosity, and is crystallization free. Suitable for room temperature applications, it gives a high gloss finish, with low surface pollution, and UV stability. This marine epoxy system has a low toxicity and should be preferred for laminating composite applications where post curing is not possible. Curing: SR5550 epoxy system cures at ambient temperature. Full cure after: 7 days at 25 oC or 48 hrs at 30 oC or 12 hrs at 40 oC or 6 hrs at 60 oC. PROPERTIES Physical properties of SR5550 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (m.Pas +-20%) at 20 oC: 1300 Density (g/cm3) at 20 oC: 1.145 Physical properties of SD5503 hardener: Aspect / colour: Yellowish liquid Viscosity (m.Pas +-20%) at 20 oC: 180 Density (g/cm3) at 20 oC: 1.00 Mix properties of SR5550 / SD5503 system: Viscosity of the mix (m.Pas +-20%) at 20 oC: 1300 Weight ratio: 100 / 29 g Volume ratio: 100 / 33 ml or 3 / 1 Reactivity of SR5550 / SD5503 system: Pot life for 100 g mix at 20 oC: 57' Exothermic temperature (oC) for 100 g mix at 20 oC: 140 Time to reach the exothermic temperature for 100 g mix at 20 oC: 1 h 05' Drying time, set to touch on 1 mm wet film at 20 oC: 3 h 30' Time before sanding at 25 oC: 8 hrs   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Marine epoxy system SR5550 / SD5502 with ultra slow hardener Each kilo includes 0.78 kg resin + 0.22 kg hardener The SR5550 is specially formulated for ambient temperature curing of marine and wood composites (laminating, bonding and protection of wood.) It has an excellent adhesion to all types of wood. It is handy, with adjustable working time, as it comes with 3 hardeners (fast, slow and ultra slow,) has low viscosity, and is crystallization free. Suitable for room temperature applications, it gives a high gloss finish, with low surface pollution, and UV stability. This marine epoxy system has a low toxicity and should be preferred for laminating composite applications where post curing is not possible. Curing: SR5550 epoxy system cures at ambient temperature. Full cure after: 7 days at 25 oC or 48 hrs at 30 oC or 12 hrs at 40 oC or 6 hrs at 60 oC. PROPERTIES Physical properties of SR5550 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (m.Pas +-20%) at 20 oC: 1300 Density (g/cm3) at 20 oC: 1.145 Physical properties of SD5502 hardener: Aspect / colour: Yellowish liquid Viscosity (m.Pas +-20%) at 20 oC: 90 Density (g/cm3) at 20 oC: 0.97 Mix properties of SR5550 / SD5502 system: Viscosity of the mix (m.Pas +-20%) at 20 oC: 1150 Weight ratio: 100 / 28 g Volume ratio: 100 / 33 ml or 3 / 1 Reactivity of SR5550 / SD5502 system: Pot life for 100 g mix at 25 oC: 1 h 05' Exothermic temperature (oC) for 100 g mix at 20 oC: 40 Time to reach the exothermic temperature for 100 g mix at 20 oC: 2 h 15' Drying time, set to touch on 1 mm wet film at 20 oC: 4 h 20' Time before sanding at 25 oC: 12 hrs   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Epoxy system SR Surf Clear EVO / SD EVO with fast hardener for translucent laminates Each kilo includes 0.71 kg resin + 0.29 kg hardener Surf Clear epoxy system is specially formulated for the manufacturing of wind-surf boards and surf boards. It is adapted for hand lay up of carbon, aramid, glass and HMP fabrics and is compatible with all core materials and foams. SR Surf Clear EVO resin characteristics: - Very tough epoxy resin with high thermo-mechanical performance. Recommended for high performance wave and slalom wind surf boards and sandwich (or not sandwich for wave riding surf) construction. - Creates ultra light composite parts with high mechanical resistance and UV stability. - For surface preparation / plug finishing, high-gloss requirements. - Other applications: Jewellery, coating of coloured patterns, prototypes.   Surf Clear EVO epoxy resin is manufactured with a bio-based carbon content of about 40%.   System characteristics: - Very good UV stability - Hardening without tack - High gloss - Low viscosity - Transparency of laminates - Self leveling - Scratch resistance Instructions for application: Work in a clean environment with heating facility. Working temperature: 20 oC minimum, 35-40 oC maximum. Maintain a constant temperature during lamination. Avoid high ambient humidity (< 70%). Avoid exposure to UV during cure. Laminates and coatings have a polymerization cycle of 14 days at 25 oC. Post curing offers greater UV resistance. Do not wet sand laminates or coatings before 4 days at 25 oC. Do not dilute with acetone, ester or alcohol based solvents. Keep packaging well sealed as hardener is sensitive to carbonic gas and humidity. A polyurethane paint finish can be applied without primer after sanding the final layer of resin. PROPERTIES Physical properties of SR Surf Clear EVO epoxy resin: Appearance / colour: Light purple liquid Viscosity (mPa.s) at 20 oC: 2925 ± 575 Density (g/cm3) at 20 oC: 1,1817 Physical properties of SD EVO Fast hardener: Appearance / colour: Water clear liquid Viscosity (mPa.s) at 20 oC: 190 ± 40 Density (g/cm3) at 20 oC: 1.000 Mix properties of SR Surf Clear EVO / SD EVO Fast system: Mix viscosities (mPa.s) at 20 oC: 2000 Mixing ratio by weight: 100 g / 41 g Mixing ratio by volume: 100 ml / 50 ml (2 / 1) Reactivity of SR Surf Clear EVO / SD EVO Fast system: Exothermic temperature (°C) 150 g mix at 20 oC: 225 Exothermic peak time of 150 g mix at 20 oC: 15' Pot life of 150 g mix at 20 oC: 8'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Water clear casting epoxy system SR Green Cast 160 / SD7160 Each kilo includes 0.70 kg resin + 0.30 kg hardener Water clear, low odor epoxy system, designed for decorative parts and jewelry prototyping, where a high transparency finish is required.   SR Green Cast 160 epoxy resin is manufactured with a bio-based carbon content of about 37%. SR Green Cast 160 / SD7160 system: The SR Green Cast 160 / SD7160 system exhibits very slow reactivity that allows casting of thick sections in one operation, without a change in color. With almost no odor during application, it hardens at room temperature, but in order to get the full mechanical properties (excellent resistance to thermal and physical shocks,) a post-cure from 40 to 80 oC is advised. Curing time: Curing time depends on the quantity of mix for casting, geometry of the part, thermal conductivity of mould and ambient temperature. SR Green Cast 160 / SD7160 system is very slow on small castings. To reduce cycle time, we advise to try several levels of temperature during the cure, in order to control the exothermic temperature in the part. Advised post cure cycle: Let cure at ambient temperature. Then increase the thermal properties of the system by a post-cure of 24 hours 40 oC or 8 hours at 40 oC + 12 hours at 60 oC. PROPERTIES Physical properties of SR Green Cast 160 epoxy resin: Aspect / Colour: Water clear liquid Viscosity (mPa.s) at 20 oC: 850 ± 170 Density (Kg/l) at 20 oC: 1.17 Physical properties of SD7160 hardener: Aspect / Colour: Water clear liquid Viscosity (mPa.s) at 20 oC: 125 ± 20 Density (Kg/l) at 20 oC: 0.97 Mix properties of SR Green Cast 160 / SD7160 system: Weight ratio: 100 / 42 g Volume ratio: 100 / 50 ml Mix viscosity (mPa.s) at 20 oC: 360 Reactivity of SR Green Cast 160 / SD7160 system: Exothermic temperature (°C) of 500 g mix at 20 oC: 23,5 Exothermic peak time of 500 g mix at 20 oC: 21 h 30'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Fast and clear epoxy system SR8500 / SZ8525 for hot process Each kilo includes 0.80 kg resin + 0.20 kg hardener Low viscosity epoxy system formulated for large scale production, short cycle times and hot process: 10 minutes at 100 oC or 20 minutes at 90 oC. PROPERTIES Physical properties of SR8500 epoxy resin: Aspect / colour: Clear to light yellow liquid Viscosity (mPa.s) at 20 oC: 9800 (+-1000) Density at 20 oC: 1.17 (+-0.01) Physical properties of SZ8525 hardener: Aspect / colour: Light yellow liquid Viscosity (mPa.s) at 20 oC: 33 (+-5) Density at 20 oC: 0.94 (+-0.01) Mix properties of SR8500 / SZ8525 system: Weight ratio: 100 / 25 Volume ratio: 100 / 30 Mix viscosity at 20 oC: 1800 (+-400) Reactivity of SR8500 / SZ8525 system: Pot life on 100 g mix at 23 oC: 85'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  SR8500 / KTA311 epoxy system for cold (or hot) preimpregnation Each kilo includes 0.83 kg resin + 0.17 kg hardener SR8500 / KTA311 is a 2 component, slow reactivity, solvent and reactive diluent free matrix system, designed for manual, (hand,) in-house fabric preimpregnation. Before mixing, the 2 components have a storage life of at least 1 year. After mixing and impregnation, the resulting preimpregnated fabric develops the desired tack at room temperature, and may be placed in a freezer. The out (of the freezer) life of this prepreg is at least 1 month. Consequently, this system is a versatile, cost effective solution that helps small production facilities to reduce their stock, and avoid keeping large quantities of various kinds of prepregs in the freezer. Curing temperature range is from 80 to 150 oC. Applications: Fabric preimpregnation by hand or machine, filament winding and adhesives. Particularly useful also for very large parts and hot press moulding. PROPERTIES Epoxy resin SR8500: Aspect / colour: Yellowish viscous liquid Density (kg/L) at 20 oC: 1.176 ± 0.005 Viscosity (mPa.s) at 20 oC: 9 800 ± 1000 Hardener KTA311: Aspect / colour: White viscous liquid Viscosity at 20 oC: 9000 ± 2000 Density at 20 oC: 1.13 Mix properties of SR8500 / KTA311: Mix viscosities (mPa.s) at 20 oC: 5700 Weight ratio: 100 / 21 g Volume ratio: 100 / 22 ml Tack evolution: Let at 23 oC for 48 hours or 16 hours at 40 oC   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Flexible epoxy system SR8160 / SD815B4 with slow hardener Each kilo includes 0.83 kg resin + 0.17 kg hardener SR8160 / SD815B4 is a system designed for laminating parts that exhibit shock and impact resistance, like the underbody of off road car racing. It may be used alone or as an additive to modify other epoxy systems. Also, it may be used to impregnate the outer layer(s) of laminates (so to take first contact of impacts,) and to achieve anisotropic behavior (in terms of thickness) of a part. In this case special care should be taken so to prevent delamination by making a gradual transition from elastic to rigid matrix. This gradual transition can be achieved by using 2 or 3 progressively lower content ratios (on subsequent fabric layers) of SR8160 system, so to go from pure elastic to more rigid epoxy gradually. A very high ambient temperature is needed for pure SR8160 flexible system to start the hardening reaction. Description: - 80 to 110 % of elongation at break in tension - Shock resistance over 150 KJ / m2 - Unfilled and translucent - Advantages compared to polyurethane: Does not foam when in contact with humidity Memory of shape Applications: - Parts under vibrations, shocks, low temperature - Flexible laminates: Body parts for cars, motorbike, 4X4 etc - Casting and inclusion (degassing under vacuum) - Part design / prototyping Minimum curing cycle: 24 hours at ambient temperature + 6 hours at 40 oC + 10 hours at 60 oC PROPERTIES Physical properties of SR8160 epoxy resin: Aspect / colour: Yellowish viscous liquid Viscosity at 20 oC (mPa.s): 7800 Density at 20 oC (kg / l): 1.144 Physical properties of SD815B4 hardener: Aspect / colour: Clear liquid Viscosity at 20 oC (mPa.s): 24 Density at 20 oC (kg / l): 0.98 Mix properties of SR8160 / SD815B4 system: Mix viscosities at 20 oC (m.Pas +- 20 %): 2750 Weight ratio: 100 / 20 g Volume ratio: 100 / 24 ml Reactivity of SR8160 / SD815B4 system: Time taken to achieve exotherm at 30 oC: 4h   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Heat resistant epoxy system SR1660 / SD7820 with slow hardener Each kilo includes 0.76 kg resin + 0.24 kg hardener Epoxy system developed for high service temperature tooling from 120°C up to over 200°C continuously depending on the chosen hardener. It exhibits excellent chemical resistance, resistance to oxidization and low exothermic peak. Suitable for laminating, press moulding, casting or injection.    Slow hardener SD7820: Epoxy system for parts or tooling with a service temperature up to 120°C, 160°C peak.   Applications: Composite tooling for "120°C" prepreg, thermoforming tooling or structural parts with a high service temperature. PROPERTIES Physical properties of SR1660 epoxy resin: Aspect / colour: Yellow liquid Viscosity (m.Pas) at 20 oC / 68 oF: 8500 ± 1500 Density at 20 oC / 68 oF: 1.15 ± 0.01 Physical properties of SD7820 hardener: Aspect / colour: Clear to yellow liquid Viscosity (m.Pas) at 20 oC / 68 oF: 80 ± 15 Density (g/cm3): 0.96 ± 0.01 Mix properties of SR1660 / SD7820 system: Weight ratio: 100 / 32 g Volume ratio: 100 / 39 ml Mix viscosity (m.Pas) at 20 oC / 68 oF: 2400 ± 500 Reactivity of SR1660 / SD7820 system: Exothermic peak on 500 g mix (oC) at 20 oC:180 oC Time to reach exothermic peak at 20 oC / 68 oF: 6 h   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Heat resistant epoxy system SR1660 / SD1305 with ultra slow hardener Each kilo includes 0.76 kg resin + 0.24 kg hardener Epoxy system developed for high service temperature tooling from 120°C up to over 200°C continuously depending on the chosen hardener. It exhibits excellent chemical resistance, resistance to oxidization and low exothermic peak. Suitable for laminating, press moulding, casting or injection.   Ultra slow hardener SD1305: Epoxy system for parts or tooling with a service temperature up to 140°C, 180°C peak.   Applications: Composite tooling for “140°C” prepreg, thermoforming tooling or structural parts with a high service temperature. PROPERTIES Physical properties of SR1660 epoxy resin: Aspect / colour: Yellow liquid Viscosity (m.Pas) at 20 oC / 68 oF: 8500 ± 1500 Density at 20 oC / 68 oF: 1.15 ± 0.01 Physical properties of SD1305 hardener: Aspect / colour: Dark yellow liquid Viscosity (m.Pas) at 20 oC / 68 oF: 278 ± 50 Density (g/cm3): 0.991 ± 0.01 Mix properties of SR1660 / SD1305 system: Weight ratio: 100 / 32 g Volume ratio: 100 / 39 ml Mix viscosity (m.Pas) at 20 oC / 68 oF: 4000 ± 800 Reactivity of SR1660 / SD1305 system: Exothermic peak on 500 g mix (oC) at 40 oC: 85 oC Time to reach exothermic peak at 40 oC: 2 h   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Fire resistant epoxy laminating system SR1126 / SD1305 with ultra slow hardener   Each kilo includes 0.85 kg resin + 0.15 kg hardener   Auto extinguishing laminating epoxy system. It creates low smokes and low toxicity smokes. It exhibits good temperature resistance and is bromine free. With high temperature or fire, the system expands, producing solid char barrier that protects inner materials from heat and flames. This system allows to get UL94 V0 and FAR 25 laminate parts as well as AIRBUS and BOEING standards concerning fumes and fume toxicity (please see data sheet for all details concerning FAR 25 and UL94 V0 approvals).   Ultra slow hardener SD1305: Suitable for large parts, long pot life and hot process. Tg – onset / DSC = 130 °C. Post cure at 120 °C minimum   PROPERTIES Physical properties of SR1126 epoxy resin Aspect / colour: White viscous liquid Viscosity (mPa.s) at 15 oC: 15000 ± 3000 Density at 20 oC / 68 oF: 1.28 ± 0.01   Physical properties of SD1305 hardener Aspect / colour: Yellow to red liquid Viscosity (mPa.s) at 20 oC / 68 oF: 278 ± 50 Density (g/cm3) at 20 oC / 68 oF: 0.990 ± 0.005   Mix properties of SR1126 / SD1305 system Weight ratio: 100 / 18 g Volume ratio: 100 / 23 ml Mix viscosity at 20 oC / 68 oF: 4200 ± 800   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  High temperature epoxy system SR1710 / SD7820 Each kilo includes 0.73 kg resin + 0.27 kg hardener High temperature epoxy system specially formulated for oven temperature or autoclave conditions curing. It is used for production of high performance and high temperature resistant parts with outstanding mechanical properties in sectors such as motorsport, aerospace, and many more. It is also used for manufacturing of temperature resistant molds. It has low viscosity allowing fast wetting of reinforcements, and exhibits excellent adhesion properties to all types of fibers. It is very handy for most demanding applications, with a very long working time (~ 8 hours at 20° C). It can also be used to step up production to higher temperature resistance, as it can be demolded after a relatively low temperature postcuring. Heat treating to resist higher temperatures may very well come as a second step or at a later time. For this reason this system is very useful when we have to work with plugs or molds that do not resist high temperatures. The initial minimum curing before demolding is 12 hrs at 40° C or 6 hrs at 60° C. PROPERTIES Physical properties of SR1710 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (m.Pas) at 20 oC / 68 oF: 1450 +- 150 Density at 20 oC / 68 oF: 1.15 (+-0.010) Physical properties of SD7820 hardener: Aspect / colour: Clear liquid Viscosity (m.Pas) at 20 oC / 68 oF: 60 +- 4 Density (g/cm3): 0.957 Mix properties of SR1710 / SD7820 system: Weight ratio: 100 / 36 g Volume ratio: 100 / 43 ml Mix viscosity (m.Pas) at 20 oC / 68 oF: 550 Reactivity of SR1710 / SD7820 system: Pot life on 500 g mix at 20 oC: 5 h 52' Exothermic peak on 500 g mix (oC) at 20 oC: 155 Time to reach exothermic peak at 20 oC / 68 oF: 6 h 55'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  High temperature epoxy system SR1720 / SD7840 Each kilo includes 0.79 kg resin + 0.21 kg hardener Epoxy system specially formulated for high temperature resistance. It exhibits low viscosity which makes it suitable for infusion and RTM applications. It also develops good mechanical properties after an initial posturing at low temperature, for example 50 °C, allowing parts to be demolded. This makes the system possible to be used with non heat resistant moulds and prototypes. Higher temperature resistance, up to 200 °C is possible to be achieved later, with subsequent postcuring cycles. PROPERTIES Physical properties of SR1720 epoxy resin: Aspect / colour: Yellowish liquid Viscosity (cps) at 20 oC / 68 oF: 8500(+-1500) Density at 20 oC / 68 oF: 1.18(+-0.01) Physical properties of SD7840 hardener: Aspect / colour: Reddish yellow liquid Viscosity (cps) at 20 oC: 22(+-4) Density (g/cm3): 0.97(+-0.01) Mix properties of SR1720 / SD7840 system: Weight ratio: 100 / 26 g Volume ratio: 100 / 32 ml Mix viscosity (cps) at 30 oC / 86 oF: 450(+-100) Reactivity of SR1720 / SD7840 system: Pot life on 500 g mix at 40 oC: 42' Exothermic peak on 500 g mix (oC) at 40 oC: > 250 oC Time to reach exothermic peak at 40 oC: 1h 8'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Cost / performance epoxy system R482 / H50 Each kilo includes 0.67 kg resin + 0.33 kg hardener Applications: Production of glass, aramid, carbon, and all fiber reinforced products. Hand lay-up, vacuum bagging, infusion, winding, compression, RTM and all open or closed mould fabricating in general. Positive features: Excellent cost / performance ratio, excellent impregnating, low air voids. Very good chemical resistance in the cured state. Very good filler acceptance, very mild odor. PROPERTIES Mix ratio by weight: 50 / 100 Pot life of 150 g at 25 oC: 55 min. Peak exotherm of 150 g at 25 oC: At 50 minutes 140 oC Demoulding time at 25 oC: 50 hours For safety - storage instructions please contact.   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Epoxy trowelable system Mixfill 80 for fairing Each kilo includes 0.57 kg resin + 0.43 kg hardener Mixfill 80 is a filled coating formulated based on flexibilized epoxy systems and with high mechanical performance at high percentages of elongation to break (8-15%) and a good impact resistance. Coating is filled under vacuum with a complex of very low density fillers (~ 0.6) and low abrasive power in order to ensure greater sustainability of sanding and machining without scrub tools.   Epoxy system Mixfill 80: - Excellent quality of application without microbubbles - Ease of application to the rule or the spatula - Excellent sandability with flat sanding or sander - Very low clogging of the abrasive - Great fineness of the film - No drying shrinkage during drying - Low exotherm in thick - Excellent impact resistance - Ease of dosing by volume (1/1) PROPERTIES Physical properties of Mixfill 80 base: Aspect / colour: Grey paste Viscosity (m.Pas) at 20 oC / 68 oF: 71900 ± 14400 Density at 20 oC / 68 oF: 0.6500 Physical properties of Mixfill 80 hardener: Aspect / colour: White paste Viscosity (m.Pas) at 20 oC / 68 oF: 106000 ± 21200 Density (g/cm3): 0.4800 Mix properties of Mixfill 80 system: Weight ratio: 100 / 75 g Volume ratio: 100 / 100 ml Mix viscosity (m.Pas) at 20 oC / 68 oF: 106000 ± 21200 Reactivity of Mixfill 80 system: Exothermic temperature on 500 g mix (oC) at 20 oC: 111 oC Time to reach exothermic peak on 500 g mix at 20 oC: 52' Pot life of 500 g mix at 20 oC: 34'   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Versatile epoxy system SR1610 / SD2613 for fairing Each kilo includes 0.68 kg resin + 0.32 kg hardener SR1610 / SD2613 is a versatile epoxy formulation designed to mix with hollow microspheres and inorganic fillers. It can adhere to epoxy, polyester, vinylester and polyurethane resins. It is used for the manufacturing of putties for sandable coating from medium to fine grain. It exhibits temperature resistance over 100°C. PROPERTIES Mix properties of SR1610 / SD2613 system: Weight ratio: 100 / 47 g Volume ratio: 100 ml / 50 ml (or 2/1)   Reactivity of SR1610 / SD2613 system: Pot life of 500 g mix at 20 oC: 60' Working time of 3 mm thick coat of putty at 20 oC: 2 hrs Putty in a coat of 3 mm sandable at 20 oC after: 20 hrs   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  Top clear 3 component epoxy system SR TopClear 1054 / SD TopClear 1533 / ABU Each kilo includes 0.55 kg resin + 0.36 kg hardener + 0.09 kg diluent Shiny, translucent, resistant to UV, and high build epoxy system, that can be brushed or sprayed. It can be used with multiple materials, such as wood, composites, fiberglass or carbon fabrics, paper, cardboard, leather, foam, metal, stone, marble, concrete, etc. Applications: Finishing for cosmetic parts, glass / hot coat, varnishing, surfacing, laminating of small parts, carbon "look", light binding, non-structural bonding, surf board repairs, fixing fin box, table top, clear gel coat. PROPERTIES Physical properties of SR TopClear 1054 Incolore epoxy resin: Aspect: Liquid Colour: Clear to light yellow Viscosity (mPa.s) at 20 oC: 1.600 Density (Kg/l) at 20 oC: 1.07 Physical properties of SD TopClear 1533 hardener: Aspect: Liquid Colour: Clear Viscosity (mPa.s) at 20 oC: 1.000 Density (Kg/l) at 20 oC: 1.15 Mix properties of SR TC 1054 / SD TC 1533: Weight ratio: 100 / 66 g Volume ratio: 100 / 62 ml Mix viscosity (mPa.s) at 20 oC: 2.100 Gel time at 20 oC: 1h 20' Thinning / solvent properties of thinner ABU: Sprayable application: dilute from 15% to 30 % straight after mixing the resin and hardener.   Intrastat Number for this product: Epoxy: 39073000, Hardener: 29213091..

  1.00 kg set (0.76 kg resin + 0.24 kg hardener) A system of 2 liquid components that when mixed, expands into cellular foam. After cure, it becomes very tough, and exhibits high performance, unique characteristics not possible to obtain by other expanding or liquid foams like polyurethane, polystyrene etc. The PB170 / DM03 cellular foam production system expands and hardens to a final density of 170 kg / m3. The DM03 is the faster hardener. Product description The foaming products are 2 component systems (resin + hardener) developed for "in situ" low density foam production. They can be used to fill mold cavities, and avoid the use of low density fillers and/or the cost of machining of other readily expanded foams like PVC. They come white, but can be colored by adding any epoxy compatible pigment. The final density of the foam is a result of the choice of the resin. The PB170 resin provides approximately 170 kg/m3 foam. The hardener (in this case the DM03) influences only the curing time and not the potential thickness or final density of each shot (or layer) in the cast part.   The process can be separated in 2 steps: step 1: The mixed resin+hardener expand rapidly into foam step 2: The foam hardens slowly Key features: "In situ" and "in mold" manufacturing of low density foam core helps to avoid the use of low density fillers or CNC machining of expanded foams. Good adhesion onto all type of materials like prepregs and wet/dry epoxy, polyester and vinylester systems. Homogeneous density, floating volume, and very low water absorption. Can be used to increase the density of other cores and honeycomb. Foam blocks can be machined to produce models and prototypes. Physical properties of resin PB170: Color: White Viscosity at 25 oC / 77 oF: 8000 (+-1500) Density: 1.12 (+-0.01) Physical properties of hardener DM03: Color: Light yellow Viscosity at 20 oC / 68 oF: 210 (+-40) Density at 20 oC / 68 oF: 1.00 (+-0.01) Mixing ratio: 31 hardener to 100 p.b.w. resin Properties of cured system: Final density after free expansion at 20 oC / 68 oF: 170 (+-20) kg / m3 Expansion ratio at 20 oC / 68 oF: X 6.2 Thermal stability after 24 hrs at room temperature + 6 hrs at 40 oC / 104 oF: Tg1 above 50 oC / 122 oF Thermal stability after 24 hrs at room temperature + 12 hrs at 60 oC / 140 oF: Tg1 above 70 oC / 158 oF Exothermic parameters: Are the thermal conductivity of substrate, open or closed mold, geometry and thickness, temperature of materials and mold, ambient temperature, volume and mass of the casting. When casting onto a thick laminate that is curing, the heat produced by the resin system can increase the reactivity of the foaming system.   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..

  1.00 kg set (0.74 kg resin + 0.26 kg hardener) A system of 2 liquid components that when mixed, expands into cellular foam. After cure, it becomes very tough, and exhibits high performance, unique characteristics not possible to obtain by other expanding or liquid foams like polyurethane, polystyrene etc. The PB170 / DM02 cellular foam production system expands and hardens to a final density of 170 kg / m3. The DM02 is the slower hardener. Product description The foaming products are 2 component systems (resin + hardener) developed for "in situ" low density foam production. They can be used to fill mold cavities, and avoid the use of low density fillers and/or the cost of machining of other readily expanded foams like PVC. They come white, but can be colored by adding any epoxy compatible pigment. The final density of the foam is a result of the choice of the resin. The PB170 resin provides approximately 170 kg/m3 foam. The hardener (in this case the DM02) influences only the curing time and not the potential thickness or final density of each shot (or layer) in the cast part.   The process can be separated in 2 steps: step 1: The mixed resin+hardener expand rapidly into foam step 2: The foam hardens slowly Key features: "In situ" and "in mold" manufacturing of low density foam core helps to avoid the use of low density fillers or CNC machining of expanded foams. Good adhesion onto all type of materials like prepregs and wet/dry epoxy, polyester and vinylester systems. Homogeneous density, floating volume, and very low water absorption. Can be used to increase the density of other cores and honeycomb. Foam blocks can be machined to produce models and prototypes. Physical properties of resin PB170: Color: White Viscosity at 25 oC / 77 oF: 8000 (+-1500) Density: 1.12 (+-0.01) Physical properties of hardener DM02: Color: Clear to light yellow Viscosity at 20 oC / 68 oF: 130 (+-25) Density at 20 oC / 68 oF: 0.98 (+-0.01) Mixing ratio: 36 hardener to 100 p.b.w. resin Properties of cured system: Final density after free expansion at 20 oC / 68 oF: 170 (+-20) kg / m3 Expansion ratio at 20 oC / 68 oF: X 6.2 Thermal stability after 24 hrs at room temperature + 6 hrs at 40 oC / 104 oF: Tg1 above 50 oC / 122 oF Thermal stability after 24 hrs at room temperature + 12 hrs at 60 oC / 140 oF: Tg1 above 70 oC / 158 oF Exothermic parameters: Are the thermal conductivity of substrate, open or closed mold, geometry and thickness, temperature of materials and mold, ambient temperature, volume and mass of the casting. When casting onto a thick laminate that is curing, the heat produced by the resin system can increase the reactivity of the foaming system.   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..

  1.00 kg set (0.74 kg resin + 0.26 kg hardener) A system of 2 liquid components that when mixed, expands into cellular foam. After cure, it becomes very tough, and exhibits high performance, unique characteristics not possible to obtain by other expanding or liquid foams like polyurethane, polystyrene etc. The PB250 / DM02 cellular foam production system expands and hardens to a final density of 250 kg / m3. The DM02 is the slower hardener. Product description The foaming products are 2 component systems (resin + hardener) developed for "in situ" low density foam production. They can be used to fill mold cavities, and avoid the use of low density fillers and/or the cost of machining of other readily expanded foams like PVC. They come white, but can be colored by adding any epoxy compatible pigment. The final density of the foam is a result of the choice of the resin. The PB250 resin provides approximately 250 kg/m3 foam. The hardener (in this case the DM02) influences only the curing time and not the potential thickness or final density of each shot (or layer) in the cast part.   The process can be separated in 2 steps: step 1: The mixed resin+hardener expand rapidly into foam step 2: The foam hardens slowly Key features: "In situ" and "in mold" manufacturing of low density foam core helps to avoid the use of low density fillers or CNC machining of expanded foams. Good adhesion onto all type of materials like prepregs and wet/dry epoxy, polyester and vinylester systems. Homogeneous density, floating volume, and very low water absorption. Can be used to increase the density of other cores and honeycomb. Foam blocks can be machined to produce models and prototypes. Physical properties of resin PB250: Color: White Viscosity at 25 oC / 77 oF: 12000 (+-2000) Density: 1.10 (+-0.01) Physical properties of hardener DM02: Color: Clear to light yellow Viscosity at 20 oC / 68 oF: 130 (+-25) Density at 20 oC / 68 oF: 0.98 (+-0.01) Mixing ratio: 36 hardener to 100 p.b.w. resin Properties of cured system: Final density after free expansion at 20 oC / 68 oF: 250 (+-25) kg / m3 Expansion ratio at 20 oC / 68 oF: X 4 Thermal stability after 24 hrs at room temperature + 6 hrs at 40 oC / 104 oF: Tg1 above 50 oC / 122 oF Thermal stability after 24 hrs at room temperature + 12 hrs at 60 oC / 140 oF: Tg1 above 70 oC / 158 oF Exothermic parameters: Are the thermal conductivity of substrate, open or closed mold, geometry and thickness, temperature of materials and mold, ambient temperature, volume and mass of the casting. When casting onto a thick laminate that is curing, the heat produced by the resin system can increase the reactivity of the foaming system.   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..

  SG715 / SD802 epoxy gel coat system Price: 31.97 EUR / 1.27 kg set (1.0 kg resin + 0.27 kg hardener)   The SG715 / SD802 is a two component epoxy gel coat that is very easy to spread with brush or roller, and hardens practically without shrinking at room temperature. It gives a hard surface with resistance to abrasion and is easy to polish. Its thixotropic but nevertheless supple consistency makes the resin/hardener mixture easy to apply without bubbles with a shorthaired brush in a layer thickness of 1-3 mm. The SG715 / SD802 system does not run down at edges, corners and vertical surfaces. Allow to gel before applying a second coat. To avoid the risk of delamination, lamination must begin with no delay as soon as the gel coat is no longer tacky. If needed, the system can be made thinner by mixing together with other epoxy systems or epoxy solvent.   PROPERTIES Color: white and black Thermal stability: Tg1 = 90 oC / 194 oF after 24 hours at ambient temperature + 8 hours at 60 oC / 140 oF Mixing ratio: 27 hardener to 100 p.b.w. resin Pot life of 150 g at 20 oC / 68 oF: 17 minutes Curing time: 6 hours Application and curing temp: 18-30 oC / 64.4-86 oF, humidity < 80%   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..

  SG715 / SD7820 epoxy gel coat system Price: 40.75 EUR / 1.23 kg set (1.00 kg resin + 0.23 kg hardener)   The SG715 / SD7820 is a two component epoxy gel coat that can be applied with a brush, a roller or a spray gun, and hardens at room temperature. It gives a hard surface with resistance to abrasion and good thermal properties after curing (Tg1 max = 120°C (DSC)). Before applying a possible second coat or laminating, allow the gelcoat to gel. It must be tacky (still sticking on the finger) to avoid any risk of delamination. The SG715 / SD7820 is recommended for building prototypes and scale models. If needed, the system can be made thinner by mixing together with an epoxy solvent.   PROPERTIES Color: white and black Thermal stability: Tg1 max = 120°C (DSC) Mixing ratio: 23 hardener to 100 p.b.w. resin Gel time at 20 oC: 4 h Recommended post-curing cycles: 12 h at 20°C+ 24 h at 40°C or 12 h at 20°C+ 8 h at 60°C Humidity: <70%   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..

  Fire resistant SGi128 / SD228 epoxy gel coat system   Price: 89.21 EUR / 1.68 kg set (0.99 kg resin + 0.69 kg hardener)   The SGi128 / SD228 is a two component, fire resistant epoxy gel coat system, halogen free and flame retardant and has a low smokes opacity and toxicity. This system allows getting the RAILWAY standard EN45545-2: R6 HL1, HL2 and the BUILDING & CONSTRUCTION standard ASTM E84-15b: Class A. It requires post curing in the mould before the part’s release. The lamination can start when the gel is still tacky.   PROPERTIES Color: white Thermal stability: Tg1 max = 73 oC Mixing ratio: 70 hardener to 100 p.b.w. resin Gel Time at 20 oC: 6 h 40 min Curing schedule: 24 h at 25 °C or 16 h at 60 °C Humidity: < 70%   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..

  SGGCI / SDGCI S epoxy gel coat system Price: 50.60 EUR / 1.48 kg set (1 kg resin + 0.48 kg hardener)   SG GreenCoat Incolore has a good UV resistance with 51% of biobased carbon in the resin part and 37% in the final mixture.   SGGCI / SDGCI S is a two component epoxy translucent gel coat used in order to protect the laminate and improve shine of finished parts. Apply a thin layer of 0.5-0.8 mm (400-600 g/sqm) with short brush. As soon as the gel coat passes gel time but still tacky, a first layer of epoxy and fabric should be applied in order to achieve best chemical bonding. Do not use spray gun or solvents.   PROPERTIES Color: translucent Temp. resistance: 80 oC / 176 oF Mixing ratio: 100 to 48 p.b.w. (resin to hardener) Pot life of 100 g at 20 oC / 68 oF: 45 min Gel time at 20 oC / 68 oF: 2h + 30 min Curing time: 24 hours Application and curing temp: 15-30 oC / 59-86 oF   Intrastat Number for this product: Epoxy: 39073000, Hardener: 38249098..